Wilkerson 12 Series Bowl / Drain Kits User Manual download pdf

WARNING

To avoid polycarbonate bowl rupture that can cause personal

injury or property damage, do not exceed bowl pressure or

temperature ratings. Polycarbonate bowls have a 150 PSIG

pressure rating and a maximum temperature rating of 125°F.

CAUTION

Polycarbonate bowls, being transparent and tough, are ideal

for use with Filters and Lubricators. They are suitable for use in

normal industrial environments, but should not be located in

areas where they could be subjected to direct sunlight, an

impact blow, nor temperatures outside of the rated range. As

with most plastics, some chemicals can cause damage.

Polycarbonate bowls should not be exposed to chlorinated

hydrocarbons, ketones, esters and certain alcohols. They should

not be used in air systems where compressors are lubricated

with fire-resistant fluids such as phosphate ester and diester

types.

Metal bowls are recommended where ambient and/or media

conditions are not compatible with polycarbonate bowls. Metal

bowls resist the action of most such solvents, but should not be

used where strong acids or bases are present or in salt laden

atmospheres. Consult the factory for specific recommendations

where these conditions exist.

TO CLEAN POLYCARBONATE BOWLS USE MILD SOAP

AND WATER ONLY! DO NOT use cleansing agents such as

acetone, benzene, carbon tetrachloride, gasoline, toluene, etc.,

which are damaging to this plastic.

Application Limits

These products are intended for use in general purpose

compressed air systems only.

With Polycarbonate Bowl

kPa PSIG bar

Operating Pressure Maximum 1024 150 10.2

Operating Temperature Maximum 52°C (125°F)

Operating Temperature Minimum 0°C (32°F)

With Metal Bowl

kPa PSIG bar

Operating Pressure Maximum 1734 250 17.3

Operating Temperature Maximum 80°C (175°F)

Operating Temperature Minimum 0°C (32°F)

WARNING

To avoid unpredictable system behavior that can cause personal

injury and property damage:

• Disconnect electrical supply (when necessary) before installation,

servicing, or conversion.

• Disconnect air supply and depressurize all air lines connected to

this product before installation, servicing, or conversion.

• Operate within the manufacturer’s specified pressure, temperature,

and other conditions listed in these instructions.

• Medium must be moisture-free if ambient temperature is below

freezing.

• Service according to procedures listed in these instructions.

• Installation, service, and conversion of these products must be

performed by knowledgeable personnel who understand how

pneumatic products are to be applied.

• After installation, servicing, or conversion, air and electrical

supplies (when necessary) should be connected and the product

tested for proper function and leakage. If audible leakage is present,

or the product does not operate properly, do not put into use.

• Warnings and specifications on the product should not be covered

by paint, etc. If masking is not possible, contact your local

representative for replacement labels.

WARNING

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF

THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR

RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND

PROPERTY DAMAGE.

This document and other information from The Company, its

subsidiaries and authorized distributors provide product and/or system

options for further investigation by users having technical expertise. It

is important that you analyze all aspects of your application, including

consequences of any failure and review the information concerning

the product or systems in the current product catalog. Due to the

variety of operating conditions and applications for these products or

systems, the user, through its own analysis and testing, is solely

responsible for making the final selection of the products and systems

and assuring that all performance, safety and warning requirements

of the application are met.

The products described herein, including without limitation, product

features, specifications, designs, availability and pricing, are subject

to change by The Company and its subsidiaries at any time without

notice.

EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR

INCLUSION IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE

THESE PRODUCTS. CONTACT YOUR LOCAL REPRESENTATIVE.

Installation and Service Instructions:

83-959-000

Bowl Kits, Drain Kits, Bowl Guard Kits,

Sight Gauge Kits and Force Fill

Adapter Kits

ISSUED: November, 2001

Supersedes: None

EN# 01085520, Rev.1

Englewood, CO 80110

Introduction:

Follow these instructions when installing, operating, or servicing

the product.

1 2

Summary of Contents

Page 1 - WARNING

! WARNINGTo avoid polycarbonate bowl rupture that can cause personalinjury or property damage, do not exceed bowl pressure ortemperature ratings. Poly

Page 2 - Instructions

Bowl Kits, Drain Kits, Bowl Guard Kits, Sight Gauge Kits and Force Fill Adapter Kits 83-959-000Sight Gauge(GRP-96-346)Bowl Force FillAdapter(LRP-96-30

Comments to this Manuals

No comments

Wilkerson 12 Series Bowl / Drain Kits User Manual

Browse online or download User Manual for Hardware Wilkerson 12 Series Bowl / Drain Kits. Wilkerson 12 Series Bowl / Drain Kits User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Wilkerson 12 Series Bowl / Drain Kits